Products

The devices of the BSA-W2 series were developed to protect against the effects of indirect lightning discharge and induction voltage. They offer protection in zone transitions 1-2 according to IEC 62305. The BSA-W2 (4+0) contains four high-performance metal oxide varistors to protect three-phase TN-S networks with separate

N and PE conductors. In the event of a defect, the two-part device enables a simple and quick replacement without new wiring, by pulling out the plug-in module and inserting a new module. The devices have a mechanical status indicator and a remote signaling contact.

The KINASGARD® DBWF-C ceiling-mounted motion transmitter detects the presence of persons and movements and has a switching contact as an output (normally open contact). The motion detector is used for status monitoring/detection and for motion-dependent control of room functions, e.g. for lowering the temperature of unoccupied rooms.

The KINASGARD® DBWF ceiling motion sensor detects the presence of persons and movements and has a switching contact as an output (changeover contact). The motion detector is used for monitoring and detecting status conditions and for motion-dependent control of room functions, e.g. lowering the temperature of unused rooms.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

The THERMASGARD® DTF device is a small built-in resistance thermometre with passive output for in-wall installation, e.g. in plasterboard walls or suspended ceilings.

The DTF ceiling temperature measuring transducer is preferably installed in ceilings and walls. It blends in seamlessly with the overall architectural design and detects the temperature at the surface. The connecting head is pluggable for quick, easy mounting.

ISB-G group block for group formation

ISB-Z central control block, central on/off

Maintenance-free AERASGARD® RCO2-AS xx CO2 detector with traffic-light indicator and acoustic signal, self-calibrating, in an attractive plastic housing, for determining the CO2 content of the room air (0...3000 ppm). The measuring transducer converts the measurand to a standard signal, which is directly visualised by colour LEDs (traffic light indicator). An additional signal tone sounds when warning levels are reached (can be switched off via DIP switch).

Maintenance-free AERASGARD® RCO2-AS xx CO2 detector with traffic-light indicator and acoustic signal, self-calibrating, in an attractive plastic housing, for determining the CO2 content of the room air (0...3000 ppm). The measuring transducer converts the measurand to a standard signal, which is directly visualised by colour LEDs (traffic light indicator). An additional signal tone sounds when warning levels are reached (can be switched off via DIP switch).

Maintenance-free AERASGARD® RCO2-AS xx CO2 detector with traffic-light indicator and acoustic signal, self-calibrating, in an attractive plastic housing, for determining the CO2 content of the room air (0...3000 ppm). The measuring transducer converts the measurand to a standard signal, which is directly visualised by colour LEDs (traffic light indicator). An additional signal tone sounds when warning levels are reached (can be switched off via DIP switch).

Maintenance-free AERASGARD® RCO2-AS xx CO2 detector with traffic-light indicator and acoustic signal, self-calibrating, in an attractive plastic housing, for determining the CO2 content of the room air (0...3000 ppm). The measuring transducer converts the measurand to a standard signal, which is directly visualised by colour LEDs (traffic light indicator). An additional signal tone sounds when warning levels are reached (can be switched off via DIP switch).

The sensor device is installed on cooling ceilings, cooling or cold-water pipes and cooled surfaces, and has been designed to prevent the formation of condensation. It reliably detects the formation of dew by means of its humidity and temperature sensor (no conductivity measurement). Thanks to its measuring method of pro-dynamic cross-convection it yields precise measuring results (with LED status indicator). Dew point temperature is the temperature at which the air reaches the state of saturation and water vapour starts to condensate. 

The sensor device is installed on cooling ceilings, cooling or cold-water pipes and cooled surfaces, and has been designed to prevent the formation of condensation. It reliably detects the formation of dew by means of its humidity and temperature sensor (no conductivity measurement). Thanks to its measuring method of pro-dynamic cross-convection it yields precise measuring results (with LED status indicator). Dew point temperature is the temperature at which the air reaches the state of saturation and water vapour starts to condensate. 

The sensor device is installed on cooling ceilings, cooling or cold-water pipes and cooled surfaces, and has been designed to prevent the formation of condensation. It reliably detects the formation of dew by means of its humidity and temperature sensor (no conductivity measurement). Thanks to its measuring method of pro-dynamic cross-convection it yields precise measuring results (with LED status indicator). Dew point temperature is the temperature at which the air reaches the state of saturation and water vapour starts to condensate. 

The sensor device is installed on cooling ceilings, cooling or cold-water pipes and cooled surfaces, and has been designed to prevent the formation of condensation. It reliably detects the formation of dew by means of its humidity and temperature sensor (no conductivity measurement). Thanks to its measuring method of pro-dynamic cross-convection it yields precise measuring results (with LED status indicator). Dew point temperature is the temperature at which the air reaches the state of saturation and water vapour starts to condensate. 

Connection bridge for looping through the plus and minus pole of the 17.5mm supply voltage.

The HYGRASGARD® FSFM / FSFTM room humidity transmitter with in-wall housing is used for measuring the relative humidity and temperature of the air. It converts the measured values into a standard signal of 0-10 V.

A digital, long-term stable sensor is used for humidity and temperature measurement. Relative humidity [% r.H.] is the quotient of water vapour partial pressure divided by the saturation vapour pressure at the respective gas temperature.

Calibratable HYGRASGARD® RPFF - 25 / RPFTF - 25 pendulum room humidity and temperature measuring transducer with pluggable metal sinter filter, housing made of impact resistant plastic, with/without optional display. The sensor device measures relative humidity and/or air temperature and converts the measurands into a standard signal of 0-10 V or 4...20 mA. It supports with four switchable temperature ranges.